• Install the axle to wheel nut and torque to 199 ft/lbs. with a 1-5/16” socket. Do NOT re-use the stock axle to wheel nut. Use the axle to wheel nut that was supplied with your new axle.
  • 1.5" cross-over steering arm that is 7" long (with steering arm studs/nuts/cones), 3.5' draglink tube from 1.5"x.250 wall DOM tubing. This kit comes either with or without MOOG ball joints and spindle studs/nuts installed. This will also work on 1988-1998 Chevy trucks with straight axle swaps using the above year front axles. MADE IN THE USA!
  • What are the torque specs for the spindle nut...I have the service manual from the merry christmas link but it says 185 ft/lbs and that seems way too much or am I I was able to make it 10 miles before the bearings seized up and the tire nearly came off the truck.
  • Apr 16, 2010 · Start by removing the tie rod from the spindle. Remove the cotter pin, and loosen the castle nut, then with a hammer of decent weight, hit the spindle around the ball joint, you don't want to just start hammering away on the ball joint itself, so that you don't damage the threads, hence why i recommend leaving the castle nut on but loose.
  • DANA SPICER 28068X Front Spindle Nut and Washer set. 1.625-16 thread size. Includes 21588X Inner nut with pin, 36569 washer with holes for inner nut pin and 31139 outer nut. Fits Chevy and GMC k5, k10, k20 with GM 8.5 inch 10 bolt Corporate front ends.
  • Hey guys I'm working on my front disks and I wanted to know what's the torque setting on that front nut ?its a 2001 C200K. a bit expensive since i could already buy the spindles readily installed and bolt on off Ebay for like 100$ each, but i don't have proper tools to adjust the bearing play...
  • This Warn Industries Locking Hub Spindle Nut Conversion Kit is used with hub number 9790, 20990 and 29071. $93.37 Locking Hub Spindle Nut Conversion Kit - 32721 4WD Hubs & Wheels | WARN Industries When replacing factory automatic hubs with manual hubs, you must also purchase Spindle Nut Conversion Kit #27988 for ’83–’89 vehicles ...
  • Item #: TM-9 - Mount pad for TH400 and 700R4 transmission, for 1947-59 conversion or 1960-96 standard fit, one pad needed with ME833, works for Chevy or GMC trucks

Contribute guest post

The attachment bolts for a 5-bolt brake assembly like the part # AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close to that range.
Suzuki Sidekick’s 1989-2000 ( or Geo Trackers) I will use the Sidekick/Tracker name interchangeably. This is a 15,000 mile service point and more often, if you ford streams or drive in rain with bad seals in the hub (gasket and o-ring).

Resistive power divider design

1. Tighten to 8 ft-lbs (10 N-m), then tighten an additional 1/3 turn to at least 37 ft-lbs (50 N-M). Upon initial installation of replacement ball joint, tighten nut to to 81 ft-lbs (110 N-m).
/ RACE NUT: 2014 – 2015: 520 ft-lbs: MONDIAL – ALL: 2 DOOR / CPE / CAB: 1983 – 1993: 75 ft-lbs: TESTAROSSA: 2 DOOR / COUPE: 1985 – 1991: 75 ft-lbs: Make: Model: Trim: Year Range: Torque: FIAT: 124: 2 DOOR / SPIDER: 1967 – 1981: 65 ft-lbs: 124 SPIDER: 16″BASE / CONVERTBLE: 2017 – 2018: 95 ft-lbs: 500 – POP: 15″STEEL / POP: 2012 – 2018: 70 ft-lbs: 500 – POP: 15″ALUM / POP: 2012 – 2018

How to make a shape transparent in cricut design space

• HYTORC Hydraulic Torque Wrench. Rebuilding the World Trade Center. HYTORC Nut. Bolting Software.
I answered my own question when i checked out my 69-81 malibu haynes manual for all those interested here they are Upper control arm mounting nuts 50 lb-ft LH/RH lower ball joints nuts 80 lb-ft LH/RH upper ball joints nuts 60 lb-ft LH/RH front caliber bolts 40 lb-ft LH/RH front sway bar nuts 20...